• Earth grounding points on bench and floor mats are used to connect ground cords, these must be riveted through the mat material
• The punch and anvil are simple but effective tools to achieve a neat finish with firm materials, no thicker than 4mm
• Both tools are mild steel, with a bright zinc and passivate finish

Straight Earth Lead

• Low Profile cone prevents cord becoming detached
• Suitable for use with all types of ESD Matting

Material:

• Special conductive wire
• Each straight cord contains 10 special conductive wires
• Outer covered with Non-Conductive PU
• Length: 10ft (both product codes)
• Diameter of cord: 2.4 mm
• Resistivity : 1M Ohm +/- 10%

Personnel Grounding / Leads / Tools & Accessories
Straight Earth Lead / 4 Claw Snap Fastener

Additional Details:

• Straight Earth Lead – 10mm stud – ring terminal 10ft Each
• Straight Earth Lead – Conical head: 10mm stud – ring terminal 10ft Each
• One end supplied with a single ring terminal the other end features a 10mm female snap and 2 x 4mm banana sockets.

ESD Bench Matting – Textured Finish

• High quality ESD bench matting
• Reflection breaking surface to reduce glare and improve operator comfort
• Protection against small collisions thanks to natural resilience of rubber
• Prevents sliding of delicate components thanks to excellent friction coefficient
• Heat resistant: rubber does not melt or burn coming into contact with hot metal parts or soldering debris
• Resistant to chemical agents normally used for maintenance
• Oil resistance: this product resists most oils
• Suitable for loose laying: does not require application with adhesive
• Good resistance to scratches
• Excellent flexibility and comfort
• Cut mats available on request
• European origin

GROUNDING:

Sufficient ground cords should be used to reliably meet EN 61340-5-1 Table 3 less than 1 x 109 ohms for working surfaces. Industry recommendation is that continuous runs of ESD matting should be grounded at 10ft intervals to allow proper charge decay rates. Each individual ESD mat should be grounded with ground snaps located no further than five feet from either end.

CLEANING:
Please note that contact between the matting surface and any acid or alkali solvent is strictly prohibited (such as Benzene, Alcohol etc), this will result in the antistatic performance wearing away. If cleaning is required, the matting may be wiped with a cloth coated in a neutral solution (such as water).

GUIDANCE ON USE:

Matting materials have a tendency to shrink slightly when first unrolled. In applications where length is critical, allow the material to relax for at least 4 hours before cutting to size. Matting should always be trimmed with a sharp knife or razor blade.

CUTTING TOLERANCES:
Width + 6mm
Length + 6mm every linear foot of running material

RoHS COMPLIANCE:
None of the following materials are intentionally added in manufacturing this product: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE) as outlined in the Directive 2002/95/EC Article 4.1.

ESD Bench Matting – Smooth Finish

Features:
Anti-static matting should be laid out in the workshops or advanced laboratories for microelectronic industries such as electronic semi-conduct devices, electronic computers, electronic communication equipment and integrated circuits etc.

• Great value ESD Bench Matting
• Made from anti-static (conductive) and static-dissipative materials with synthetic rubber
• 2mm thick double-layer structure
• Surface layer is a 0.5mm thick static-dissipative layer
• Bottom layer is a 1.5mm conductive layer
• Available in blue, grey or green
• Asian origin

GROUNDING:
Sufficient ground cords should be used to reliably meet EN 61340-5-1 Table 3 less than 1 x 109 ohms for working surfaces. Industry recommendation is that continuous runs of ESD matting should be grounded at 10ft intervals to allow proper charge decay rates. Each individual ESD mat should be grounded with ground snaps located no further than five feet from either end.

CLEANING:
Please note that contact between the matting surface and any acid or alkali solvent is strictly prohibited (such as Benzene, Alcohol etc), this will result in the antistatic performance wearing away. If cleaning is required, the matting may be wiped with a cloth coated in a neutral solution (such as water).

GUIDANCE ON USE:
Matting materials have a tendency to shrink slightly when first unrolled. In applications where length is critical, allow the material to relax for at least 4 hours before cutting to size. Matting should always be trimmed with a sharp knife or razor blade.

CUTTING TOLERANCES:
Width + 6mm
Length + 6mm every linear foot of running material

RoHS COMPLIANCE:
None of the following materials are intentionally added in manufacturing this product: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE) as outlined in the Directive 2002/95/EC

ESD Anti Slip Multipurpose Matting – 3mm

A multi purpose, anti-static matting for use on either workstation benches or as a flooring solution in the workshops of advanced laboratories for microelectronic industries.

• Made from anti-static (conductive) and static-dissipative materials with synthetic rubber
• Corrugated surface provides slip resistance and even footing
• Excellent abrasion resistance
• Easy to clean, sweep or hose off
• Resistant to cuts, tears, impact, ozone damage, fire and most chemicals
• Available in 2 / 3 and 4mm thick double-layer structure
• Surface layer is a 1mm thick static-dissipative layer
• Available in blue and yellow surface with black textured bottom surface

GROUNDING:
Sufficient ground cords should be used to reliably meet EN 61340-5-1 Table 3 less than 1 x 109 ohms for working surfaces. Industry recommendation is that continuous runs of ESD matting should be grounded at 10ft intervals to allow proper charge decay rates. Each individual ESD mat should be grounded with ground snaps located no further than five feet from either end.

CLEANING:
Please note that contact between the matting surface and any acid or alkali solvent is strictly prohibited (such as Benzene, Alcohol etc), this will result in the antistatic performance wearing away. If cleaning is required, the matting may be wiped with a cloth coated in a neutral solution (such as water).

GUIDANCE ON USE:
Matting materials have a tendency to shrink slightly when first unrolled. In applications where length is critical, allow the material to relax for at least 4 hours before cutting to size. Matting should always be trimmed with a sharp knife or razor blade.

CUTTING TOLERANCES:
Width + 6mm
Length + 6mm every linear foot of running material

RoHS COMPLIANCE:
None of the following materials are intentionally added in manufacturing this product: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE) as outlined in the Directive 2002/95/ EC Article 4.1.

IC Workstation and Mat Cleaner

A low-ionic, general purpose workstation cleaner, which is also biodegradable, alcohol free and odorless. Formulated for use in the electronic, clean room, pharmaceutical environments. A unique formulation that is mildly cationic to effectively neutralize any static charges. Meets requirements for SARA title 3, TSCA and ESD TR20.20-2000.

Ordering Matting with Studs

Requesting Cut Mats with Studs:

If you wish to order pre cut mats with added studs, please ensure that the position of the stud is specified as per Fig 1, and quote the correct product code when ordering.

ESD Workstation Kit

Kit Includes:

• 1x ESD Matting (600x1200mm) with 10mm stud in each corner (see spec for ESD Bench Matting – Smooth Finish)
• 1x ESD Protected Area Vinyl Sign
• 1x Earth Bonding Plug 3x10mm Stud
• 1x10mm Fabric Adjustable Wrist Strap Hypo Allergenic
• 1x10mm Coiled Earth Lead
• 1x10mm Straight Lead
• 1x Crocodile Clip
• 1x Instruction Leaflet

ESD Protected Area Sign

• Antistatic coating
• Self adhesive: 0.4mm thick PVC
• 300 x 150mm Coiled Earth Lead
• Excellent quality for use with any kind of wrist band
• Strong connection between the cord and 10mm stud
• 10mm Stud / Banana Socket
• Special conductive wire, outer covered with non-conductive PU
• Each 10ft coiled cord contains 10 strands
• Diameter of cord: 2.4 mm / Diameter of coil cord: 1.02 cm
• Resistivity: 1M Ohm +/- 10% Fabric Adjustable Wrist Strap Hypo Allergenic
• Sky blue band
• Adjustable for any size of wrist
• 10mm stud
• High quality conductive interior, made of stainless steel nylon filament
• Outer side process with non-conductive nylon yarn
• Conductive back plate to cover the metal part to prevent allergic reaction
• Surface resistivity of 103Ω

Resistance from Band <105 Ohms Test Method EN 61340-55-1
Underside of Band <104 Ohms Test Method EN 61340-5-1
Top Side of Band < 106 Ohms Test Method EN 61340-5-1
Earth Bonding Plug 3x10mm Stud

• Incorporates a 3x10mm male stud for connection grounding wire
• Designed to fit UK standard mains plug outlets
• Neutral and mains voltage pins are plastic, earth pin is metal

Straight Earth Lead

• Excellent quality for use with any Field Service Kit or Table Mat
• Strong connection between the cord and stud pecial conductive wire each containing 10 special conductive wires
• Outer covered with non-conductive PU
• Length: 12ft
• Diameter of cord: 2.4 mm
• Resistivity : 1M Ohm +/- 10%